GNSS Choke Ring Antenna

With the Leica AR25, Leica Geosystems introduces the next generation of high performance choke ring antenna, covering all present and currently planned GNSS constellations and signals, including L-Band (SBAS, CDGPS and OmniStar).

For more information, please visit our website.

With emerging new satellite systems planned by the European Union (Galileo) and China (Compass/Beidou-2) GNSS networks and reference stations need to be ready to track these new upcoming signals.

 

Choke ring antennas are recognised as having the best accuracy and tracking performance compared to all other antenna types. They are widely used in infrastructure networks and reference stations today. The new Leica AR25 uses a new 3D Conic choke ring design, which extends the benefits of the original 2D design in areas such as multipath rejection and signal to noise ratio, whilst at the same time improving tracking of low elevation satellites.

Abstract

Satellite navigation is more and more important in a plethora of very different application fields, ranging from bank transactions to shipping, from autonomous driving to aerial applications, such as commercial avionics as well as unmanned aerial vehicles (UAVs). In very precise positioning, navigation, and timing (PNT) applications, such as in reference stations and precise timing stations, it is important to characterize all errors present in the system in order to account possibly for them or calibrate them out. Antennas play an important role in this respect: they are indeed the 'sensor' that capture the signal in space from global navigation satellite systems (GNSS) and thereby strongly contribute to the overall achievable performance. This paper reviews the currently available antenna technologies, targeting specifically reference stations as well as precise GNSS antennas for space applications, and, after introducing performance indicators, summarizes the currently achievable performance. Finally, open research issues are identified, and possible approaches to solve them are discussed.

Keywords:

GNSS, antenna, multipath, PNT, reference station, satellite, precise positioning

1. Introduction

The use of satellite navigation is nowadays very widespread and embraces almost all fields of modern life [1,2,3,4]. The availability of multiple constellations and new signals in the last decades enables a strong improvement in the achievable accuracy in positioning and timing. Progress in the receiver technology has also made it possible to achieve extraordinary results at lower prices, making it accessible to a wider range of users [5].

While mass-market applications have been the main driver in the technology development, GNSS still strongly rely and depend on ground reference stations for monitoring the signals sent by the satellites, as well as identifying anomalies and characterization of imperfections that can later be communicated to (professional) users, for instance, by means of augmentation systems [1].

Technological advances for reference stations were apparently stronger in the 's when the number of reference stations was growing, and therefore, the business side of it was more appealing. In the latest years, however, a revived interest in improving the technology of reference stations can be recorded, most probably due to the addition of new frequencies and new constellations in the GNSS world, with the corresponding need for updating the stations.

Furthermore, at the present stage, new scenarios are being developed, such as reference stations not placed on Earth but, for instance, orbiting Earth in low orbit (LEO) in order to achieve even better monitoring without the limitations of atmosphere and ground multipath [6].

The scope of this paper is to analyze state-of-the-art technologies in terms of antennas for GNSS in very high-performance applications, taking reference stations, both on the ground and in space, as exemplary applications. In particular, we investigate how far commercially available antennas are from what an 'ideal antenna' should be and evaluate the imperfections and their impact on the overall system performance.

Starting from big and canonically used antennas for ground reference stations, it is also investigated in what respect performance degrades when using more compact (while still high-end) antennas that could, for instance, be used as 'mobile reference stations,' both on Earth and in space.

In order to evaluate and compare the performance of the different state-of-the-art antennas, performance indicators are defined in Section 2, considering the different domains in which an antenna influences the GNSS measurement: gain roll-off, multipath suppression capability, group delay, and phase center variations are investigated.

Section 3 shows state-of-the-art performance for ground reference station antennas, while Section 4 covers high-end antennas for space applications. Section 5 then exemplarily shows the GNSS measured performance of some of the antennas. Conclusions are drawn in Section 6.

2. Performance Parameters and the 'Ideal Antenna'

Antennas for reference stations have to act as sensors to monitor the signals emitted by the satellites. Therefore, ideally, antennas should be totally transparent, i.e., capable of properly collecting the signal, without adding any distortion (in terms of amplitude, delay, etc.) to the signal [7].

Such an ideal antenna would have an omnidirectional pattern in the upper hemisphere, and it would then very sharply decrease below the horizon to not receive any signals from the lower hemisphere (e.g., from multipath). Moreover, it would be able to collect signals at all bands of interest, and its transfer function would be very constant over frequency and angle.

As a matter of fact, real antennas do not manage to achieve this ideal behavior. Due to various design techniques, approximations thereof can, however, be achieved.

In order to identify the critical parameters of an antenna for GNSS, its operation, together with the receiver, is analyzed. The calculation of position, velocity, and time (PVT) in a GNSS receiver starts from two kinds of measurement: the pseudorange measurement and carrier phase measurement [1]. The former calculates the delay in time between the signal emission at the satellite side and the signal collection at the receiver, while the second calculates the distance (in an ambiguous way) by measuring the phase at which the signal is received.

A good signal-to-noise ratio is needed in order to be able to perform the measurements in an accurate way. Moreover, it shall also be avoided that non-line-of-sight (NLOS) propagation disturbs the calculation of the distance between satellite and receiver, i.e., multipath shall be minimized [8].

In view of the above-mentioned functional needs, the relevant parameters of a receiving antenna can be summarized as follows:

1. Gain (roll-off, uniformity), affecting the amount of received power and the signal to noise level;

2. Group delay variation (GDV), affecting the pseudorange measurement;

3. Phase center variation (PCV), affecting the carrier phase measurement;

4. Multipath suppression capability, estimated through multipath suppression indicators (MPSIs), related to the amount of crosspolar radiation.

2.1. Gain Roll-Off and Uniformity

The gain of the antenna affects the amplitude of the signal available at the receiver in multiple ways. On the one hand, it is important to ensure that the signals are available at the receiver with enough power to be clearly distinguishable from noise after correlation [2]. This can be obtained by using active antennas, i.e., antennas with LNAs integrated into the antenna itself, with the purpose of strongly reducing the impact of noise of the further components (splitters, cables, etc.) between antenna and receiver, in case the two are connected through long cables or splitters. High-performing antennas should, moreover, have a uniform gain over both angle and frequency, such that the antenna itself does not introduce variations in the received signal. This uniformity is usually obtained by antenna designs using multiple feeds and hence capable of exciting very pure and uniform gain patterns [9].

In order to be able to receive signals from satellites over a wide range of elevations, high-performing antennas shall also have a gain pattern with a very broad beamwidth (defined as the angular region where the gain level is not lower than a given threshold, usually 3 or 10 dB, with respect to the maximum gain). This requirement contradicts, however, the need for the pattern to drop sharply below the horizon (to reduce the influence of reflectors). The fulfillment of both requirements, at the same time, is hardly achievable in real life, unless very big structures are used, such as the ones adopted in ground-based augmentation system (GBAS) ground reference antennas [10]. Small antennas usually have a broader beamwidth with a scarce suppression of the pattern below the horizon, while more sophisticated antennas manage to strongly suppress back lobes at expenses of beamwidth, i.e., gain at low elevations.

The amount of gain drop from the zenith to the horizon is usually termed as 'gain roll-off' [7]. As later discussed in this paper, gain roll-off is usually stronger (about 10'20 dB) for antennas with multipath-limiting structures (i.e., for which the requirement for strong suppression of the back lobe is fully satisfied). On the other hand, milder gain roll-offs are obtained for antennas with weak multipath suppression (for which, therefore, the pattern does not drop strongly below the horizon), hence resulting in a better reception of low elevation signals at the price of increased sensitivity to multipath.

2.2. Group Delay/Phase Center Variations (GDVs/PCVs)

Group delay variations (GDVs) and phase center variations (PCVs) are the relevant parameters when it comes to the accuracy of distance measurement from receiver to satellite.

For pseudorange measurements, the delay of the signal is the parameter to be 'sensed'; therefore, the receiver antenna must make sure to minimize (variations of) its group delay over angle and frequency in order not to introduce errors in the measured delay from the satellite. This parameter is particularly important for timing or aviation applications. In the first case, accurate time estimation is indeed critical and is the aim of the measurement. In the second case, pseudorange measurements are the primary means for PVT determination and are only loosely supported by carrier phase measurements (to reduce the high-frequency noise) due to safety/integrity requirements.

Similarly, for the carrier phase measurements, the phase of the signal carries the information about the distance: a uniform phase pattern of the receiver antenna ensures that no additional phase contribution due to the antenna itself is added to signals from the different satellites and therefore an accurate position can be calculated.

Methods for precisely calculating PCV have been established over the years by the geodetic community: the two most relevant ones are an electromagnetic anechoic chamber calibration and a robot-based calibration [11,12]. The characterization of GDV, on the other hand, still has no widely recognized technique; research is also ongoing in this case to establish the applicability of robot calibration, with the main challenges being the effect of pseudorange noise and multipath errors on the accuracy of the characterization. Chamber calibration appears less prone to these errors and is used by the authors in the following sections.

2.3. Multipath Suppression Capability

Finally, as already suggested, the capability to suppress multipath is one of the main characteristics of reference stations: indeed, in applications where accuracy and signal monitoring capabilities are crucial, it is necessary to ensure that measurements are not distorted by reflected signals. These signals bounce over objects, buildings, and terrains in the vicinity of the receiver antenna and then reach the antenna, overlapping with the line-of-sight (LOS) signal and therefore changing the shape of the correlation function, resulting in an error of the estimated delay/phase information from the satellite.

While traditionally, parameters from the world of telecommunications such as the axial ratio or the crosspolar discrimination have been used to estimate the multipath susceptibility [7], it was recently found by the authors that they were not fully describing the actual physics of multipath in GNSS and that parameters more GNSS-related were needed.

Indeed, axial ratio and crosspolar discrimination are calculated by using the two components of the fields (right-handed circular polarization (RHCP) and left-handed circular polarization (LHCP)) in the same direction. This might be useful for communication links but not for multipath phenomena, where the line-of-sight signal from the satellite comes from a given direction {θs, φs}, which stands for elevation and azimuth angle from the incoming signal of the satellite. Non-line-of-sight signal, which is bounced on objects around the receiver, arrives from a different direction {θMP, φMP}, which stands for elevation and azimuth angle of the incoming MP. In order to take this into account, new parameters have been recently defined by the authors and called 'multipath susceptibility indicators' (MPSIs) [13], based on modified versions of the crosspolar discrimination factor (XPD) and of the down-to-up-ratio (DUR).

Different MPSIs can be defined according to the physics of the multipath, e.g., for reflections reaching the receiver antenna from negative or positive elevations, MPSIdown or MPSIup, respectively.

They are defined as follows [13]:

MPSIup={log20('XPDmax,db) if XPDmax,db<00 if XPDmax,db>0

MPSIdown={log20('DURmax,db) if DURmax,db<00 if DURmax,db>0

with

XPDmax=max (GainLHCP(θ>0,'φ))GainRHCP(θs,φs) 

DURmax=max (GainTOT(θ<0,'φ))GainRHCP(θs,φs)

An MPSI close to 0 means that the multipath is barely suppressed by the antenna; on the other hand, an MPSI of about 0.75 means that the multipath will be attenuated 10 dB with respect to the direct signal, and hence, a medium capability is available. Finally, MPSI values higher than 1 stand for very good multipath suppression given by the antenna. The aforementioned parameters will be used, when possible, in the next Sections to compare the available designs.

3. State-of-the-Art of Antennas in Ground Reference Stations

All GNSSs need a monitoring station network as part of the ground segment to monitor the satellite signals and feed observation to control stations to counteract accordingly if needed.

GPS has for instance a monitor station network (MSN) made of 16 stations (6 from the air force and 10 from NGA) [14]. Galileo on the other hand uses a network of Galileo Sensor Stations (GSSs) spread all over the world [15]. In addition, the Galileo Experimental Sensor Stations (GESSs) are used for monitoring the Galileo system performance.

Furthermore, national and international geodetic communities are also maintaining networks of monitoring stations, such as the IGS or the EUREF network [16,17].

Additional resources:
OCXO Manufacturer A vs. Manufacturer B: Which is Better?
How to Choose the Right OCXO Manufacturer for Your Needs?
Why Are Crystal Oscillator Manufacturers Key Innovators?
Seam 2520 Quartz Crystal: Insights and Trends for 2024
What to Consider When Buying OEM Kitchen Tableware?
What to Consider When Choosing OEM Robot Vacuum Supplier?

For more information, please visit mide.

Due to the different operators and the evolution over time of the stations, several different antennas are currently operated at the different stations: the most common ones are for sure antennas based on choke-ring technology, capable of strongly limiting multipath from negative elevations. Examples of commercial products making use of this technology are Leica AR25, Novatel GNSS-750, Javad RingAnt-DM, Trimble TRM, and TRM.

In the following, the performance of commercial antennas is analyzed: if available at DLR, they have been characterized in DLR's semi-anechoic chamber, as shown in . Due to the number of plots, all figures regarding this characterization are included in the Appendix A, , , , , , , , , and .

Open in a separate window

Most of these antennas are relatively big in size and have a diameter larger than 30 cm. However, recent GNSS antennas with reduced 'size, weight, and power cost (SWAP)' have been introduced for high-performance applications: they are addressed in Section 3.2 in order to understand if their performance is also acceptable for reference station applications.

3.1. Antennas with Lateral Size Larger Than 30 cm

Among the canonical antennas for reference stations, the first subgroup comprises choke-ring antennas that are typically used as static reference antennas. In this analysis, measurements for the Leica AR25 antenna, the Novatel GNSS-750, and the Javad RingAnt-DM are available, and the first two are shown in .

Open in a separate window

Leica AR25 and Novatel GNSS-750 have both a gain roll-off factor of about 10'11 dB for the L1/E1 band and a factor of 14 dB or 13 dB for the L5/E5 band, respectively. Javad Ring Ant-DM shows slightly higher gain roll-off factors of 16 dB for L1/E1 and for L5/E5 band: signals from low-elevation angles are received with a lower C/N0 in this antenna, compared with the former two antennas.

The measured PCV for the frequency bands L1/E1 and L5/E5 are shown in Appendix A. The three choke-ring antennas exhibit a mostly uniform behavior for the PCV over the upper hemisphere, with a maximum range of values of 7.4 mm and 8.2 mm for the Leica AR 25, 8.4 mm and 9.2 mm for the Novatel GNSS 750, and 17.6 mm and 14.5 mm for the Javad RingAnt-DM in the frequency bands L1/E1 and L5/E5, respectively. In general, the PCV has a stable behavior along azimuth and shows variations mostly along the elevation angle, with a 'bump' at medium elevations; Javad RingAnt-DM has greater variations among the three.

The GD exhibits absolute mean values around 20'21 ns for Leica AR25 and Novatel GNSS-750 and 18.6 ns for Javad RingAnt-DM, in the L1/E1 band, and values around 19 ns for Leica AR25, 18.8 ns for Novatel GNSS-750, and 21.4 ns for Javad RingAnt-DM in the L5/E5 band. All antennas show a mostly stable behavior of the GDV within the upper hemisphere, with a maximum range of 1.3 ns, 0.8 ns, or 1.2 ns, respectively. Some azimuthal variations are to be seen for Leica AR25 and Javad RingAnt-DM at L1/E1, however, within the range of 0.5 to 0.8 ns.

All three choke-ring antennas achieve a good MPSIup, with values above 0.75 in the L1/E1 band from zenith (elevation of 90°) to approximately 15°'20° elevation, enabling the suppression of most multipath from positive elevations. Javad RingAnt-DM is, in this case, performing better than the other antennas, with higher values of MPSI for medium/high elevations, due to its stronger crosspolar discrimination (i.e., low LHCP) throughout the upper hemisphere.

For the L5/E5 band, all three antennas exhibit very good values for MPSIup, being close to 1 or even higher at the zenith, becoming lower for decreasing elevation angles, however, still reaching values of approximately 0.5 at the horizon in the L5/E5 band. This behavior can be explained by the low level of LHCP gain in the upper hemisphere for the L5/E5 band, compared to the LHCP gain levels in L1/E1. The MPSIdown has a similar behavior for all three choke-ring antennas for both frequency bands. They exhibit good MPSIdown values, between 0.8 and 1.0 in higher elevation directions. Additionally, in this case, JavadRingAnt-DM performs slightly better, due to its stronger roll-off, clearly indicating that the antenna was optimized for multipath suppression.

An approach different from choke rings, still leading to similar weight/size, was chosen by Topcon in the PN-A5 antenna, in which instead of choke rings, vertical metallic pins aligned along a semihemispherical ground plane are used to reduce the back radiation. This antenna was not available at DLR: datasheet information [18] shows, however, that the gain roll-off factor is similar to the one from the three choke-ring antennas, being 10 dB for the L1/E1 band and 12 dB for the L5/E5 frequency band.

For Galileo monitoring stations in ESA's Time and Geodesy Validation Facility (TGVF-X), the Galileo Experimental Antenna (GalExpAnt) from Space Engineering is used (see ).

Open in a separate window

Though having a similar size and weight to the choke-ring designs shown before, the technology used in this case is not clearly specified. As later discussed, its performance would not mirror the benefit of choke rings for what concerns multipath suppression. The antenna was characterized by DLR and results can be seen in Appendix A. A gain roll-off factor between 6 and 11 dB for the L1/E1 band and around 11'12 dB for L5/E5 is found. At the L1/E1 band, the RHCP gain does not show minimal variations along the azimuth, indicated by the spread of gain values for different azimuth cuts. At L5/E5, the gain in RHCP is more uniform and changes only slightly along the azimuth.

GalExpAnt exhibits PCV variations within a range of about 10.8 mm for L5/E5 and 22.3 mm for L1/E1. In this case, PCV shows changes along the elevation angle, as was the case for Javad RingAnt-DM or Novatel GNSS-750, in addition to quite significant differences along the azimuth, especially in the L1/E1 frequency band up to 12 mm difference in lower elevations. The GD shows absolute values around 64.8 ns for L1/E1 and 45 ns for the L5/E5 band. The measurements show GDV along elevation with a maximum range of values of 1.9 ns, as well as along the azimuth within maximum a range of 1.2 ns for both L1/E1 and L5/E5 bands.

The MPSIup for this antenna exhibits moderate values around 0.5 in the zenith direction, with values strongly decreasing already at middle elevations, suggesting a poor multipath suppression capability of this antenna at L1/E1. For the L5/E5 band, on the other hand, MPSIup exhibits good values (in the range of 0.6'0.8) in the zenith direction until elevation angles of 15°. Similar behavior can be seen for MPSIdown. At L1/E1, the values change along the azimuth, and even in the zenith direction, the MPSIdown only reaches values of about 0.5, decreasing further for lower elevation angles. In L5/E5, it shows a more uniform behavior along azimuth, with good values of 0.75 at the zenith, but with values below 0.3 already at elevations around 30°, showing also, in this case, a nonoptimal multipath suppression capability for satellites signals coming from low elevations (and multipath from lower hemisphere).

Efforts to reduce the received multipath with the GalExpAnt were, for instance, documented in [19], resulting in an absorbing structure engineered around the antenna and contributing to strongly reducing the amount of multipath impinging on the antenna, in addition to making the installation much more complicated and expensive.

Though GalExpAnt appears particularly not optimal for multipath suppression, similar efforts in reducing errors caused by multipath for ground stations but resulting in complicated designs were also proposed for further antennas from the US side: modifications around a choke-ring antenna have been investigated, e.g., in [20], also in this case strongly complicating the overall antenna structure.

A further design, developed internally by DLR, is presented here as well and is shown in ; this antenna is based on the technology shown in [21] but includes choke rings for multipath suppression as well.

Open in a separate window

A similar (but reconfigurable) version of the antenna is shown in [22]. The antenna exhibits a gain roll-off factor of 17'18 dB for L1/E1 and L5/E5, hence similar to Javad RingAnt-DM. The pattern is for both frequency bands quite uniform along the azimuth. Its PCV values vary in a maximum range of 17.5 mm for L5/E5 and 14.7 mm for the L1/E1 band, being slightly higher than the PCV of Javad RingAnt-DM. This is due to the relatively high absolute values close to elevation angles of 0°, whereas in medium/higher elevation angles the PCV exhibits lower variations than Javad RingAnt-DM. The mean GD for this antenna shows very low values, compared to the aforementioned antennas, with absolute values around 2.5 ns for L1/E1 and 6.6 ns for L5/E5. This is due to the fact that the antenna (at the time of measurement) was still passive, i.e., was not integrating active components, strongly contributing to the mean value of group delay. An active version of the design is currently being manufactured. Variations of GD over angle are in the range of 0.7 ns at both frequency bands.

MPSIup at L1/E1 and L5/E5 appears particularly good, with values around 1.0 in zenith direction and bigger than 0.3 for elevations higher than 15°. MPSIdown, similar to the COTS choke-ring antennas analyzed before, has values close to 1 at zenith and bigger than 0.3 for elevations higher than 15°.

In conclusion, the antennas analyzed in this subgroup show high performance in terms of pattern uniformity, gain roll-off, stable PCV/GDV, and very good multipath suppression. However, differences in performance can be observed among the different products, such that a careful antenna selection (considering the parameters that will be more relevant for the installation scenario) is strongly advisable before installation.

3.2. Antennas with Lateral Size Smaller Than 30 cm

The next subgroup consists of three high-precision GNSS antennas that are smaller in size and lighter in weight than the previously considered antennas, as they are not equipped with a choke ring or a similar structure to reduce multipath. Measurements were performed at DLR and can be compared more in detail in this analysis for Novatel 703-GGG, NavXperience Nav3G+C, and Tallysman Verostar VSE, shown in .

Open in a separate window

Novatel 703-GGG [23] shows a mostly uniform behavior of the RHCP gain and a gain roll-off factor of 11'12 dB in L1/E1 and between 8 and 10 dB in L5/E5, with slight variations along the azimuth. Nav3G+C [24] has a gain roll-off factor between 11 and 14 dB for L1/E1 and 9'10 dB for L5/E5 and shows small gain variations along the azimuth. Tallysman VSE [25] has a smaller gain roll-off, of only about 6'9 dB in L1/E1 and 7'10 dB in L5/E5.

Regarding PCV, Novatel 703-GGG shows very low PCV, with a maximum value range of 2.2 mm for the L5/E5 band and 4.5 mm for the L1/E1 band. PCV appears stable throughout the whole upper hemisphere. Nav3G+C exhibits PCV with a maximum range of 10.3 mm for L5/E5 and 5.7 mm for the L1/E1 band and small changes along elevation. Tallysman VSE, on the other hand, has a PCV in the range of 18.1 mm in L5/E5 and 8.1 in the L1/E1 band with a slight azimuth dependence.

When looking at group delay, Novatel 703-GGG shows GD mean values around 18.7 ns for L1/E1 and 20.6 ns for L5/E5, being rather stable within the upper hemisphere (i.e., with a range of 0.6 ns). Nav3G+C has absolute GD values around 7.7 ns and 9.0 ns for L1/E1 and L5/E5, respectively, and is also quite uniform within the upper hemisphere (with a maximum variation range of 0.7 ns). Tallysman has absolute GD values of 14 ns at L5/E5 and 28 ns at L1/E1, with a variation range up to 1.4 ns along elevation.

Both Novatel 703-GGG and Tallysman VSE show very good behavior for the MPSIup, with values around 1 for the whole upper hemisphere for L1/E1 and between 0.7 and 0.8 for L5/E5. MPSIup for Nav3G+C is also very similar to the one of Novatel 703-GGG antenna with good values between 0.8 and 1.0 for the whole hemisphere at L5/E5, while it has only good performance (though still comparable to the choke rings) for L1/E1. The MPSIdown exhibits for both Novatel 703-GGG and Nav3G+C antennas good values in zenith direction, while goes below 0.3 for elevations smaller than 20°. The multipath susceptibility for Tallysman VSE is poor at both bands, with MPSIdown values bigger than 0.3 already reached at elevations of 30° due to the lower back lobe suppression and roll-off.

In conclusion, smaller high-performance antennas are available on the market capable of strongly minimizing PCV/GDV and achieving a very broad beamwidth. In this case, multipath suppression is often not one of the main design goals, and therefore, poor performance can be obtained by some designs. However, some commercial products, such as Novatel 703-GGG, appear to have a very good balance between size and multipath suppression capability.

A summary of the performance achievable by the different antennas is given in : a qualitative assessment of their performance in terms of multipath is also given with a 'simplified' scale of + and -. Moreover, data for further commercial antennas, as obtained by their datasheets, are also included in the table for completeness.

Table 1

AntennaTechniqueSizeWeightFrequency BandsGain Roll-Off Factor Multipath Suppression MPSIup /MPSIdown Phase Center Variation PCV (Maximum Range in mm)Group Delay Variation GDV (Maximum Range in ns)Leica AR25 [26]Chokering380 × 380 × 200 mm37.6 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 14 dB
L1/E1: 10 dB L5/E5: +++/+
L1/E1: +/+ L5/E5: 8 mm
L1/E1: 7 mm L5/E5: 0.8 ns
L1/E1: 1.3 ns Novatel GNSS 750 [27]Chokering380 × 380 × 200 mm37.6 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 13 dB
L1/E1: 11 dB L5/E5: +++/+
L1/E1: +/+ L5/E5: 9 mm
L1/E1: 8 mm L5/E5: 0.4 ns
L1/E1: 0.8 ns Javad RingAnt DM [28]Chokering380 × 380 × 138 mm34.4 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 16 dB
L1/E1: 16 dB L5/E5: +++/++
L1/E1: ++/++ L5/E5: 15 mm
L1/E1: 18 mm L5/E5: 0.8 ns
L1/E1: 1.2 ns Space Engineering GalExpAnt Not specified294 × 294 × 459 mm3~16 kgE5ab, E6, E1 L5/E5: 11'12 dB
L1/E1: 6'11 dB L5/E5: +/o
L1/E1: -/- - L5/E5: 11 mm
L1/E1: 22 mm L5/E5: 1.9 ns
L1/E1: 1.7 ns DLR antenna Chokering~350 × 350 × 300 mm3~8 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 17'18 dB
L1/E1: 17'18 dB L5/E5: ++/++
L1/E1: ++/++ L5/E5: 18 mm
L1/E1: 15 mm L5/E5: 0.6 ns
L1/E1: 0.7 ns Septentrio PolaNt Chokering B3/E6 [29]Chokering376 × 376 × 350 mm35.0 kgL5/E5ab, L2, E6, L1/E1L5/E5: 11 dB
L1/E1: 11 dBn.a.n.a.n.a.Trimble GNSS v2 Chokering antenna [30]Chokering 380 × 380 × 146 mm34.3 kgL5/E5ab, L2, E6, L1/E1L5/E5: -
L1/E1: -n.a.n.a.n.a.Topcon CR G5 [31]Chokering380 × 380 × 155 mm34.9 kgL5/E5ab, L2, E6, L1/E1L5/E5: 16.5 dB
L1/E1: 13 dBn.a.n.a.n.a.Topcon PN A5 [18]Vertical dipoles380 × 380 × 262 mm36.7 kgL5/E5ab, L2, E6, L1/E1L5/E5: 12 dB
L1/E1: 10 dBn.a.n.a.n.a.Leica AR10 [32]Planar structure with large GND plane240 × 240 × 140 mm31.1 kgL5/E5ab, L2, E6, L1/E1L5/E5: n.a.
L1/E1: n.a.n.a.n.a.n.a.Novatel 704-X [33]NoVAtel's patented Pinwheel ® technology185 × 185 × 69 mm30.468 kgL5/E5ab, L2, E6, L1/E1L5/E5: 11 dB
L1/E1: 14 dBn.a.n.a.n.a.Novatel 703-GGG [23]Pinwheel ® 185 × 185 × 69 mm30.500 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 8'10 dB
L1/E1: 11'12 dB L5/E5: +++/-
L1/E1: +++/+ L5/E5: 2 mm
L1/E1: 4 mm L5/E5: 0.6 ns
L1/E1: 0.3 ns Novatel GNSS 850 [34]Multi-point feeding network176 × 176 × 55 mm30.507 kgL5/E5ab, L2, E6, L1/E1L5/E5: 12 dB
L1/E1: 10 dBn.a.n.a.n.a.Tallysman Verostar VSE [25,35]VeroStar TM technology106 × 106 × 39 mm30.080 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 7'10 dB
L1/E1: 6'9 dB L5/E5: ++/- -
L1/E1: ++/- L5/E5: 18 mm
L1/E1: 8 L5/E5: 1.1 ns
L1/E1: 1.4 ns Navxperience Nav3G+C [24,36] Mobile172 × 172 × 121 mm30.384 kgL5/E5ab, L2, E6, L1/E1 L5/E5: 9'10 dB
L1/E1: 11'14 dB L5/E5: +++/-
L1/E1: +++/+ L5/E5: 10 mm
L1/E1: 6 mm L5/E5: 0.3 ns
L1/E1: 0.7 ns Septentrio/TallysmanVeraPhase [37]VeraPhase ® 167 × 167 × 175 mm30.820 kgL5/E5ab, L2, E6, L1/E1L5/E5/L2: 11 dB
L1/E1: 13 dBn.a.n.a.n.a.Septentrio PolaNt-x MC [38]Mobile190 × 190 × 73 mm30.450 kgL5/E5ab, L2, L1/E1L5/E5: 11 dB
L1/E1: 11 dBn.a.n.a.n.a.Open in a separate window

The results shown till now demonstrate that the bigger (choke-ring) antennas clearly exhibit the best performance in terms of high gain roll-off factor and multipath suppression, particularly for the lower hemisphere, while also ensuring low and stable PCV and GDV. Smaller high-precision antennas also showed that a very good performance can be achieved also with smaller sizes: very good performance in terms of PCV/GDV stability can be obtained also in this case. Indeed, the absence of the choke rings is beneficial in achieving pattern uniformity.

However, as expected, the capability of smaller antennas to suppress multipath is, in general, poorer, in particular for reflections coming from the lower hemisphere. Good results can, however, be obtained when the requirement for multipath suppression is taken into consideration in the antenna design by using smaller and simplified multipath limitation structures, such as the Pinwheel technology used in Novatel 703-GGG, leading to only slightly worse performance than the ones obtained with much bigger and heavier choke-ring antennas.

6. Open Research Issues

Former sections showed the achievable performance for current antennas for high-performance applications. It was shown how important it is to characterize their performance parameters properly, as they will affect the power level and quality of the received signals. In general, the importance of choosing proper antennas for the specific installation should be emphasized: in complicated installation scenarios, such as rooftops, or in situations where the minimization of multipath effects is a key factor, a strong emphasis should be given to antennas providing very good multipath suppression, often coupled with strong gain roll-off factors. Moreover, for precise applications, clear preference should be given to antennas exhibiting minimal GDV/PCV, such that the antenna itself contributes minimally to the overall error. In applications where size and cost are constrained a specific trade-off should be found, taking into consideration the specific requirements.

It was also seen how state-of-the-art designs for reference station antennas tend to have large size and weight and that recent new designs have been suggested and come to the market with smaller SWAP-C factors. Miniaturization is for sure an open research issue that will also need to be tackled in the future; indeed, smaller SWAP-C models while retaining optimal performance (mostly in terms of multipath suppression, with choke rings being the most established and heavy countermeasure for that) will need to be achieved.

A further open research challenge is the addition of interference suppression capability to the design of reference station antennas. As a matter of fact, reference station performance can degrade due to both non-human factors, such as installation-related multipath and unintentional or intentional interference (both in terms of jamming and spoofing): this threat appears to gain momentum in the last years, with disruptions to ground stations documented already in [55], happening more and more often in the latest years.

A powerful countermeasure to interference (both for detection and suppression) is represented by multiantenna systems, capable of dynamically placing nulls (i.e., strongly suppressing the received power) in the direction of the interference. Adaptive multiantenna systems can also be valuable with respect to multipath suppression, using also in this case nulls in the direction of multipath.

Such systems have been widely demonstrated for robust applications in the world of research (see, e.g., [56,57]), and products are already commercially available (see, e.g., Novatel GAJT product family).

Research is, however, still needed in order to harmonize robustness and precision requirements. The adaptive nulling creates a variable pattern, with nulls provoking changes in phase and amplitude of the pattern also in their vicinity, hence possibly affecting the performance of the antenna for precision applications. Work is currently being performed in this respect at multiple institutions worldwide.

7. Conclusions

In this work, a review of GNSS antennas as sensors for high-end satellite navigation applications, in particular targeting reference station applications and space applications, was performed. The most relevant performance indicators for such kinds of applications were identified and used for comparing multiple commercial antennas, making use of anechoic chamber measurement data. Field tests were also performed, validating the former results. It was demonstrated that antenna design directly impacts the achievable performance and that the antenna to be used in a specific scenario should be selected considering which performance is most critical for the envisaged use.

Furthermore, GNSS antennas for space use were also evaluated and achievable performance was shown: due to the current new space trend and the strong increase in the number of satellites being launched, it is expected that high-performance space-qualified antennas will also see a strong increase in the near future. Open research issues were discussed and the main trends identified, namely, the quest for miniaturization (without sacrificing performance) and for the addition of interference suppression capabilities, for instance, by making use of multiantenna technologies.

Acknowledgments

The authors would like to thank S. Schön and his team (Leibniz University Hannover) for providing the Novatel 703GGG antenna for measurement, ESA, and GMV for providing the GalExpAntenna for measurement as well as ANYWAVES for providing PCV data of their antenna. Moreover, they would like to thank S. Hehenberger for the support with the PCV/GDV calculation.

Author Contributions

Conceptualization, S.C. and M.S.; methodology, S.C.; software, S.C., M.S. and M.-S.C.; validation, S.C., W.E., and M.-S.C.; writing'original draft preparation, S.C. and M.S.; writing'review and editing, all authors. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest.

Footnotes

Publisher's Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.